Aervoe 60-Watt Power Cell User Manual download pdf

120V AC Wall Charger includes:

Power Cord

Power Supply

LED Indicator

Storage Case

12V DC V

ehicle Charger

Barrel Power Adapter

Laptop Adapter

Cable

Adapter Tips including:

Apple®

SolaDyne®/Wind ‘N Go®

Micro USB

Power Cell

USB Adapter Cable

Laptop Tips

CHARGING

The Power Cell may be charged at the same time it is operating other devices. For optimum

charge time, disconnect all other devices while charging and disconnect once a full charge is

reached or when stored for more than a day. It is recommended that the Power Cell be charged

every 30 days.

LCD DISPLAY AND CHARGING INFORMATION

• Press the ON/OFF BUTTON for 3 seconds to turn the Power Cell ON or OFF. The LCD

will illuminate and display the default 5V voltage and the BATTERY METER will show the

existing battery capacity (1 bar shows a low battery, 4 bars is a fully charged battery).

When charging, the Meter will blink and it will stop blinking and all 4 bars will be shown

when fully charged. The Power Cell will automatically shut down if idle for 10 minutes.

• Low battery protection: If the battery level becomes too low a beep will sound to alert

you to recharge. If not recharged quickly the Power Cell will shut down.

• Overcharge protection: Once a full charge has been achieved, the internal charge

controller will prevent overcharging. However, it is best to remove power source once

charging is complete.

• Automatic overload, temperature, and short circuit protection will automatically power off

the Power Cell if it detects over limit ranges. To reset you will need to power it back up

using any of the above charging methods.

120V AC Wall Charging (adapter included):

1. Connect the POWER CORD to the POWER SUPPLY. Plug the male DC output plug into

the DC IN PORT of the Power Cell and then plug the 120V AC WALL CHARGER into an

electrical outlet.

2. The LED INDICATOR on the AC charger will be red during charging and turn green when

charging is complete.

3. If the Power Cell fails to charge, check to make sure all connections are secure.

12V DC Vehicle Charging (adapter included):

1. Plug the male DC output plug into the DC IN PORT of the Power Cell and then plug the

12V DC VEHICLE CHARGER into a 12V power receptacle.

2. If the Power Cell fails to charge, check to make sure all connections are secure.

Solar Charging (not included):

The instructions below are for Sierra Wave Solar Collectors #9510 or #9530.

1. Connect the 12V DC VEHICLE CHARGER to the DC IN PORT of the Power Cell.

2. Plug the 12V end of the VEHICLE CHARGER into the barrel power adapter that comes

with the solar collector. Then connect it to the solar collector. For the #9510 use the 15V

DC port on the Power Port Hub and for the #9530 plug it directly into the DC Out cord.

3. Follow the instructions included with your solar collector. Solar charging will be most

effective on a bright sunny day. Repositioning the solar panel throughout charging will be

required to capture the best angle of the sun.

4. If the Power Cell fails to charge, check to make sure all connections are secure.

LAptop AdApteR tIps

#4717 (4.70mm x 4.75mm) HP, ASUS, LG

#5010 (5.50mm x 4.75mm) Samsung, LG

#5517 (5.50mm x 4.75mm) ACER

#5521 (5.50mm x 4.75mm) HP, ACER, NEC, Toshiba

#5525 (5.50mm x 4.75mm) HP, ACER, NEC, Toshiba

#6014 (5.50mm x 4.75mm) Sony

#6330 (5.50mm x 4.75mm) NEC, Sony, Toshiba

#7406 (7.40mm x 4.75mm) HP, Dell

DC Out Por

USB Out Port DC InPort

oltage Selection

Button

ON/OFF

Button

LCD Display Shows

Battery Meter

Voltage Selection

Charging Activity

Sierra Wave

60-Watt Power Cell #9660

The 60-Watt Power Cell is a dependable source of portable power to operate a variety of portable

electronic devices. The Power Cell is capable of providing different power outputs to support

the voltage requirements of different portable electronic devices. It may be charged from the

included adapters or from optional Sierra Wave solar collectors (sold separately). Once charged,

the high-capacity lithium ion batteries and intelligent circuitry provide reliable power for your

devices such as smart phones, MP3/iPods, eReaders, tablet and laptop computers, cameras,

and more.

IMpoRtANt sAFeGUARds

Read all instructions before operating

WARNING to reduce the risk of electric shock, injury, or damage to this product:

• Do Not submerge the unit or its accessories in any liquid or use in wet weather

• Do Not short circuit, expose to heat, ﬁre, cause damage to the batteries, or reverse

polarity (+/-)

• Do Not disassemble due to risk of injury

• Do Not use in ﬂammable or explosive areas

• Do Not block vents or cover unit during use

• Discontinue use if electronic components or wires are exposed

• Store in a clean dry place when not in use

• Administer close supervision when using around children

THERE ARE NO USER SERVICEABLE PARTS. ALL REPAIRS MUST BE PERFORMED BY AERVOE

INDUSTRIES, INC. OR AN AUTHORIZED REPAIR FACILITY. FAILURE TO FOLLOW THESE

GUIDELINES CAN DAMAGE THE UNIT, CAUSE INJURY, AND VOIDS THE PRODUCT WARRANTY.

CALL AERVOE FOR ADDITIONAL INSTRUCTIONS OR TROUBLESHOOTING INFORMATION.

pARts IdeNtIFICAtIoN

UsING stoRed poweR

CAUtIoN: Before use, conﬁrm that your electronic device is compatible with the Power Cell

using the listed speciﬁcations. Failure to follow these instructions could result in damage to

your device or the Power Cell. Only use the included adapters or other quality adapters matching

these speciﬁcations. Make sure the Power Cell has between 2 and 4 bars on the BATTERY

METER before charging another device.

SELECTING OPTIONAL VOLTAGE

• Check your device’s operating instructions for speciﬁcations related to choosing the

right DC Out voltage. Select the appropriate Voltage Output by pressing the VOLTAGE

SELECTION BUTTON and cycling through the available options: 5V, 9V, 12V, 16V, 19V or

21V. Choosing the wrong voltage output will not allow proper charging and may cause

damage to your device or the Power Cell.

• Once a voltage is selected it will be locked-in to prevent accidental voltage changes,

which could cause damage. To select another voltage your device must be detached ﬁrst.

DEVICE CHARGING INSTRUCTIONS:

• Once connected to your device using any of the methods below, turn on the Power

Cell and your device will immediately start charging. Charging can be veriﬁed by small

moving dots in the LCD DISPLAY under the voltage selection. Once charging is complete,

unplug it from the Power Cell.

• Some Apple

devices may display “this device is not supported” if the proper voltage is

not selected or if the battery level is too low. Fully charge the Power Cell and verify the

correct voltage before retrying.

USB Output (5V/2A):

• May be used simultaneously with other DC OUTPUTS to charge other devices (except for

9V selection).

• Connect your device speciﬁc USB charging adapter to the USB OUT PORT and the other

end to your device. Or use the included USB ADAPTER CABLE and TIPS and plug the

male end of the CABLE into the USB OUT PORT of the Power Cell. Plug the appropriate

TIP into your device.

DC Output (9V, 12V, 16V, 19V & 21V):

• BARREL POWER ADAPTER (included)

1. Use this adapter to charge using your device’s 12V vehicle charger.

2. Plug the BARREL POWER ADAPTER into the DC OUT PORT of the Power Cell.

3. Connect your 12V vehicle charger into the BARREL ADAPTER and the other end

into your device.

• LAPTOP CONNECTION

IMPORTANT: When using a Dell brand laptop, please note the following. It is not

possible to charge the internal battery using the Power Cell. It can only operate the

laptop directly from the Power Cell, due to built-in controls by Dell. To override, remove

the internal battery to operate the laptop and prevent the DELL compatibility error code.

For all other laptop brands the Power Cell can charge the internal battery or directly

operate the laptop. However, if the laptop fails to charge from the Power Cell then

remove the laptop battery and retry.

1. Select either 16V, 19V, or 21V depending on your model requirements. Laptops

will not charge on any of the other voltage selections.

2. Connect the LAPTOP ADAPTER CABLE to the appropriate LAPTOP TIP, plug the

TIP into your laptop, and the other end into the DC OUT PORT.

1 2

Summary of Contents

Page 1 - 60-Watt Power Cell #9660

120V AC Wall Charger includes: Power Cord Power Supply LED IndicatorStorage Case12V DC Vehicle ChargerBarrel Power AdapterLaptop Adapter CableAdapt

Page 2 - Power Cell

opeRAtING INstRUCtIoNs60-Watt Power CellteCHNICAL INFoRMAtIoNspeCIFICAtIoNsBATTERY SPECIFICATIONS 19,800 mAh/3.7V lithium ion rechargeable battery60-7

Comments to this Manuals

No comments

Aervoe 60-Watt Power Cell User Manual

Browse online or download User Manual for Power suppliers Aervoe 60-Watt Power Cell. Aervoe 60-Watt Power Cell User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Power suppliers Aervoe 60-Watt Power Cell